Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are many accidents entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the person ahead can not be located, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowed width of the path and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not use the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift motorist did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start has to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the pole must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no challenges overhead. When the lots is traveling, the fork must not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the website traffic rules in the factory and should keep a specific safety range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when stacking or filling. .
8. The elevation of the lots have to not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, neither to drive throughout the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it has to drive securely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between both forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is prohibited to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork Electric Forklift Truck for Warehouse to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The tons needs to be stabilized with very little back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make Stand-on Electric Pallet Stacker use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and cooling water ought to be added.
2. Check the safety and security efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. During the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the exterior leakage must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive throughout the slope. When the gradient is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Solitary fork procedure is not allowed.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844